top of page
小ロット部品製作
1個からのワンオフ及び小ロット(数十個)に特化した製法で現存台数の少ない、レアな車両向けにも部品を作成できます。
一般的にはプラスチックやゴム部品を製作するには高額な金型が必要となります。
同じ部品で数万個という数を製作するのであれば最適ですが、
古い車両に関しては車両自体が何台残っているのか…
ましてや個人の旧車乗りの方がなかなか手の出せる製法ではありません。
そこで、簡易的な型を作成し必要分の部品を製作していきます。
簡易的な型のため、型自体の耐久性が低いので1個から10個ほどの
部品製作に向いています。
製作できる主な具体例は以下の通りです。
●クリアレンズ類(よくあるエポキシレジン等での複製法ではありま
せんのですぐに白化してしまうことはありません。)
●プラスチック部品
ABSのような弾性のある部品やエンジニアプラス チックのような高強度も実現可能です。
●ゴム部品
高強度のウレタンゴム系から耐油ゴムまで作成可能。
ゴムの硬さも指定可能です。
●電装ハーネス
詳しくは”配線引き直し”のページでご紹介いたします。
※製作物のサイズの大きさ・形状・お預けいただけるマスター部品の状態によって金額は変化してまいりますので、お気軽にお問い合わせください。
メールでのお問い合わせの場合は、
・製作したい個数
・大まかな3方向のサイズ(縦×横×高さ)
・簡単にで結構ですので全体の写真
をご記入いただけますと幸いです。
製作部品例

Triangular window rubber for Mazda Carol

ランチア モンテカルロ 外装部品
左右対称部品ですが、現存するのは片側のみ…ということで対称部品も新規作成いたしました。

Air flap gear for Benz G class
We received a request from a shop specializing in classic Benz. Reproduced based on the original parts on the left. The material has been devised so that it can withstand practical use. It actually works perfectly and works!

Shift knob (ebonite)
A rubber-like shift knob used in old cars. I can't find it when I look for it. It can be manufactured with hard plastic, and the design of the shift pattern in the photo can be changed.

Interior parts (resin parts)

Subaru 360 Pedal Rubber
Made of wear-resistant rubber material.
The hardness of the rubber can also be changed.
The hardness of the rubber can also be changed.

S800 clear lens
It will be the lens at both ends of the tail. There seems to be an orange lens, but a request for clearing ... I don't know much about that, but the product is perfect!

Subaru 360 side turn signal lens
This is the first product in our shop.
When I think about it now, there are places where the surface finish and the details of the details are a little ..., but the materials and equipment handled have changed a lot, so I dare to post it as a good memory (bitter smile).
When I think about it now, there are places where the surface finish and the details of the details are a little ..., but the materials and equipment handled have changed a lot, so I dare to post it as a good memory (bitter smile).

DODGE Ram Charger Tail Light
This was a consultation from an individual.
The lens was damaged and the repair marks were conspicuous.
I'm quite familiar with American cars and parts, so I contacted the site and seemed to have searched for it, but I couldn't find it ...
Since the lens itself is large, it will be an expensive category, but I asked for it because it is a car that I will ride for the rest of my life.
The lens was damaged and the repair marks were conspicuous.
I'm quite familiar with American cars and parts, so I contacted the site and seemed to have searched for it, but I couldn't find it ...
Since the lens itself is large, it will be an expensive category, but I asked for it because it is a car that I will ride for the rest of my life.

Honda S800 horn button
It is a horn button for Honda S. The upper part of the image is the one at that time, and countless cracks can be seen from the photograph. If this happens, it will be difficult to repair ...

License plate light lens
The left end is damaged and it is totally whitened. There is already some damage to the lens mounting screws. (Especially countersunk screws ...)

Mysterious lens
Create a clear lens based on the orange lens on the top. As I learned later, it was surprisingly surprising ... It seems that it was for Mazda Bongo ... It's not a very old car, but please contact us regardless of whether it's an old car or a neoclassical car.

Knob
It seems to be for old vehicles, but it is a knob part of the heater cock. Although it was a request from a domestic old car shop, we made a heater cock knob for a lifetime because it is for minor models.

Bike handle grip
This is a request from an individual customer.
It seems that the material of the grip that I used until then is bad, and my hands turn black every time I ride a motorcycle!
I heard that I like the design, so I made it based on that part.
You can also specify the hardness.
It seems that the material of the grip that I used until then is bad, and my hands turn black every time I ride a motorcycle!
I heard that I like the design, so I made it based on that part.
You can also specify the hardness.

Uncut lens
Create an uncut lens based on a genuine lens cut type. When converting the tail light to LED, the purpose was to make the LED grains look beautiful.

Interior parts
It will be the lid of the accessory case attached to the dashboard. The grain processing peculiar to the vehicle is also reproduced.

Subaru 360 fuel tank cap rubber

Side turn signal assembly for Jimny
It is a side turn signal of the first 2 stroke Jimny.
I'm impressed that it's Jimny's style to forcibly process and install other models when it deteriorates and can no longer be used, but there is also a flow of original return ...
I'm impressed that it's Jimny's style to forcibly process and install other models when it deteriorates and can no longer be used, but there is also a flow of original return ...

Ashtray handle
It is an interior part and is an ashtray puller. As usual, an on-parade of cracks in thin meat. Insert screws can also be embedded. By the way, I don't see ashtrays in recent cars ...

Motorcycle tail light lens
It consists of a main body, a clear lens, and a reflector.

Overrider
I was ashamed to say that I didn't know the word "overrider" until I received this case.
It's a shock absorbing rubber attached to the bumper to protect the car body when it hits the bumper of the car.
The surface of the requested product is in a tattered state due to deterioration over many years.
There is no problem because it is not copied exactly as it is!
It's a shock absorbing rubber attached to the bumper to protect the car body when it hits the bumper of the car.
The surface of the requested product is in a tattered state due to deterioration over many years.
There is no problem because it is not copied exactly as it is!

Harness Glomet
Looking for Glomet is always a difficult task when rewiring. Of course, it is necessary to process and install a general-purpose product with the manufacturer's discontinued number, but in most cases it does not fit well. Since it can be manufactured in the same size and dimensions as the original, the atmosphere inside the engine room is perfectly determined!

Drink tray
There is a dent in the center console like an accessory case, but I started by wondering if I could make a drink holder that fits comfortably there. Now you can enjoy the drive gracefully while drinking coffee (laughs)

Toggle switch knob
It's a very plain part, but it's a toggle switch knob (made of plastic).
The above three are also original reproductions, but I made an original switch with the same style!
The bluetooth on the left also works fine.
The above three are also original reproductions, but I made an original switch with the same style!
The bluetooth on the left also works fine.

S800 side emblem
Changed from the original "S800" to "S850". It has been plated and colored. S660 is also an ant (laughs)
bottom of page